
FH SMD Miniature Quartz Crystal Ceramic (NKS2)
Diodes IncorporatedTCC-2026-10-19-fh-smd-miniature-quartz-crystal-ceramic-nks2
FH series miniature surface-mount quartz crystals provide 12 MHz to 66 MHz frequency generation in a 2.5 mm × 2.0 mm ceramic package.
Introduction
Diodes Incorporated’s FH series comprises miniature AT-cut quartz crystal resonators for frequency generation in space-constrained electronics. The series covers fundamental-mode frequencies from 12 MHz to 66 MHz in a 2.5 mm × 2.0 mm ceramic surface-mount package.
Its configurable frequency tolerance, load capacitance, operating-temperature range, and temperature stability allow designers to select characteristics appropriate to a particular timing requirement rather than relying on a single fixed configuration.
What it does
The FH series provides a quartz-based frequency reference for electronic systems. Frequency calibration tolerance options are ±10 ppm, ±20 ppm, or ±30 ppm, while available load capacitances span 7 pF to 32 pF; series-resonant configurations are also offered.
Operating-temperature options extend from −20°C to +70°C, −40°C to +85°C, and −40°C to +125°C. Temperature-stability choices depend on the selected range, from ±10 ppm options over the narrowest stated range to ±70 ppm over the widest. Maximum first-year aging is specified as ±3 ppm at −25°C.
Maximum equivalent series resistance varies with frequency: 150 Ω from 12 MHz to 19.9 MHz, 80 Ω from 20 MHz to 29.9 MHz, and 60 Ω from 30 MHz to 66 MHz. The typical drive level is 10 µW, with a maximum of 100 µW.
Applications
Based on its frequency-control function, miniature package, and stated intended uses, the FH series can be considered for:
- Wireless and portable electronics
- Computing systems
- Data-storage equipment
- Communications hardware
- Other space-constrained designs requiring a 12 MHz to 66 MHz quartz frequency reference
Design considerations
The selected crystal configuration should match the required nominal frequency, load capacitance, calibration tolerance, operating-temperature range, and temperature-stability target. Drive level must remain within the stated 100 µW maximum, and the frequency-dependent ESR limits should be considered when integrating the resonator.
The 2.5 mm × 2.0 mm ceramic package is intended for surface-mount assembly. Components are supplied on 8 mm tape in reels of 3,000 units, supporting automated placement. The specified maximum reflow condition is +260°C for no more than 10 seconds.
The series is tested against stated methods for leak integrity, solderability, vibration resistance, solvent resistance, terminal strength, and resistance to soldering heat. It is also identified as RoHS compliant and lead-free.
Availability and further information
The Mouser Electronics source link on this page provides distributor information for the FH series. The linked datasheet contains further electrical, mechanical, ordering, and qualification details needed to select and integrate a specific crystal configuration.
Specifications
| Manufacturer | Diodes Incorporated |
|---|---|
| Part number | TCC-2026-10-19-fh-smd-miniature-quartz-crystal-ceramic-nks2 |
| Series | FH |
| Technology | AT-cut quartz crystal |
| Package | 2.5 mm × 2.0 mm ceramic |
| Mounting | Surface mount |
| Release date | 2026-10-19 |
| Leak testing | JESD22-A109 Condition C gross leak and Condition A1 fine leak |
| Solderability | J-STD-002 |
| Frequency range | 12 MHz to 66.0000 MHz (fundamental) |
| Terminal strength | MIL-STD-883 Method 2004 |
| Solvent resistance | JESD22-B107 |
| Maximum drive level | 100 µW |
| Typical drive level | 10 µW |
| Vibration resistance | JESD22-B103 |
| Load capacitance options | 7 pF to 32 pF or series resonance |
| Maximum first-year aging | ±3 ppm at -25°C |
| Maximum shunt capacitance | 5 pF |
| Maximum reflow temperature | +260°C for 10 s maximum |
| Tape-and-reel configuration | 8 mm tape, 3000 units per reel |
| Resistance to soldering heat | J-STD-020C Table 5-2 |
| Maximum ESR, 30 MHz to 66 MHz | 60 Ω |
| Minimum insulation resistance | 500 MΩ at 100 VDC |
| Operating temperature options | -20°C to +70°C; -40°C to +85°C; -40°C to +125°C |
| Maximum ESR, 12 MHz to 19.9 MHz | 150 Ω |
| Maximum ESR, 20 MHz to 29.9 MHz | 80 Ω |
| Frequency calibration tolerance options | ±10 ppm, ±20 ppm, or ±30 ppm |
| Temperature stability, -20°C to +70°C | ±10 ppm, ±20 ppm, ±30 ppm, or ±50 ppm |
| Temperature stability, -40°C to +85°C | ±30 ppm or ±50 ppm |
| Temperature stability, -40°C to +125°C | ±50 ppm or ±70 ppm |
